Showing posts with label paisley. Show all posts
Showing posts with label paisley. Show all posts

Sunday, 16 June 2019

25 snowflake challenge

Pin It now!
Yesterday Dorota of Land of Laces announced her intention of designing and posting a new snowflake every Sunday till the end of the year. A minimum of 25 snowflakes.
I shouldn’t, but I did jump right in. And in less than 24 hours I have my own pattern all ready to post!
The challenge doesn’t call for originals, but just like the 40 Blossoms sprigs I challenged myself to, let’s see if I can be as successful with this. It will stretch me for sure, but hopefully I’ll out the better for it.
I will work all snowflakes in white Anchor size 40. Since I don’t want to be spending all my time perfecting each presentation, I will share the basic pattern with the prototype itself. I welcome you to test any you like and share your experience or any errors. And if you send me a pic of your work, I might be tempted to create a proper pdf by including your model.

The challenge is open to all but pics must be posted on a Sunday to facebook and/or Instagram and tagged to @landoflaces. And at the end of 25 snowflakes, send in a ‘group’ photo!

So here’s my first pattern as is.….

Paisley Snowflake
pattern with prototype
This 2-round snowflake can be worked in one pass by climbing out with a split ring, mock picot, and smaller split ring.
TWoT Note : Depending on how one climbs out and works the initial rings, the direction of the paisleys may change.
In Anchor size 40, it measures 6cms tip to tip.

Techniques used in prototype: rosette, picot join to right, 2 shuttles, ctm, fs/bs tatting, thrown/floating rings, lock join, Josephine Ring.
Abbreviations:
-  = picot ; + = join ; dnrw = do not reverse work ; rw = reverse work ; TR = thrown ring [switch shuttle before and after each thrown ring] ; JR = Josephine ring (with half stitch count)

Round 1 - Rosette :
ring : (4 - 3 – 3 – 4 ) x6. Join each ring to previous and the last ring to first. Tie & cut.

Round 2 – Paisley :
ring1: 6 + 6. dnrw
ring2: 6 +(to next petal) 6. rw
chain: 4, (TJR1: 8), 3, (TR2: 5 – 3 – 2), 3,
(TR3: 2 + 5 – 5 – 2), 3, (TR4: 2 + 7 – 9) rw
          chain: 15, lock join (to TR4). turn work, switch shuttle
          chain: 2 (- 2) x12. rw
REPEAT from ring1 for a total of 6 arms. Tie, cut and hide ends.

I can think of so many little tweaks to improve the design. For instance –
  • the Josephine Ring is barely visible due to the overlap. Perhaps if it were a small ring, instead of JR?
  • I like the overlapping arms, though.
  • There could be a JR at the tip of each arm to make it a bit more pointed. Now the snowflake looks more like a flower, right?
  • There could be picots along one side of the thrown rings to mirror the long picoted chains?

What do you think? Requesting brutal criticism!

Saturday, 28 February 2015

Tatting Techniques : Inverted Tatting - 1

Pin It now!
Warning : This post is Not for the weak-hearted, eye-candy-loving, perfectionists :-)
I am posting this as my process-documentation ….

Inverted Tatting – Inverted Learning !


In early 2014, I was so impressed by Judith Connors’ exquisite 3-D flowers & compositions with inverted tatting, that I plunged right in. And plunged in the deep end ! Went straight for 3-D tatting. I would start a piece, reach midways, then wouldn’t know how to proceed because the thread had a mind of it’s own ! Drowning, & obviously frustrated, I discontinued the exercise, promising myself to get more techniques, skills & practice under my belt, before taking it up again.
I had shared these on InTatters at the time, but the pic quality was bad; hence have re-photographed them ….
So first off, here’s what I made then, sometime in March 2014.

Revisiting  after  One  year !

Inverted Tatting was still not on my horizon this early . But, well, Judith recently posted a picture of beginner level Beaded Damselfly on Craftree & I felt that I could probably tackle that. Now this piece is more 2-D, & it struck me that hey, This is the end I should’ve dipped my toe in first ;-P
So here are my latest ( I did not attempt the Damselfly, simply played around). Again, not good, but I can see my own slight improvement with a few do’s & don’ts for future practice (that are shared below, some of which were instructions by Judith herself) & definitely something I can go back to repeatedly, trying new shapes, etc. till I really improve. 
 

Lessons  learned  so  far :

  • Use fine thread, preferably perle cotton. The variegated green, and the brown were in Anchor size 20 (last year), & latest white are in size 40. Unfortunately, no perle cotton.
  • Start with simple, equidistant , equi-length picots. It is easier to come back & join as in a mirror-image.
  • Lock join should be Tight ! Gives a neater, even, more pleasing look.
  • Gradually increase the number of LJs in a single picot. I have made a few with 2 joins in the white paisley.
  • Tension is Crucial. Lots of practice required there.
  • Do not tug/snug the stitches too much ! My mistake in initial attempts, in order to convert to 3-D, was to really tug at the chain. It just ends up distorting the whole piece !!!
  • Do not take extreme close-ups Until you have good pieces to show, lol !
  
Tutorials  referred  to  so  far include (click on each for direct link) :
I will add these & more resources to my Tatting Resources page, as I come across them in future.

What is Your favorite tutorial & tip for Inverted Tatting ?


A  Little  about  Inverted  Tatting
And here is what Judith Connors said about her 3-D projects :
“These samples use an inversion technique, an idea of Elgiva Nicholls and developed by To De Haan-Van Beek in 'New Dimensions in Tatting' (English translation from Dutch). It uses two shuttles and sometimes a tapestry needle. It's like sculpting with threads.”



That’s it for the present. As you can well see, I need tons of practice here ! 
And this technique might well take quite a few posts in future :-)