Gotham Towers

Snowflake #22 in Land of Laces’ 25 Snowflake Project

Taking in view the majority opinion in previous post, this is the 3^rd round added to the snowflake. Since it has numerous possibilities (time is running out, & I am involved in helping out friends ;-P), I am counting it as #22, with 3 more to go. 

ConcentriCITY Towers snowflake

pattern

For some reason I was just not into this round – I hated my tatting, the curves in the chains were not sitting right, so many options kept invading my head, and I just slogged through somehow. I was almost on the verge of calling the 25 snowflake project over. After blocking it, though, I am fairly satisfied, and want to continue on.

Rounds 1 & 2 remain the same as shared here.

The only difference is the small ring at the tips is (3-3) instead of 5ds.

Since one tatter preferred written instructions, here is the entire written pattern. Choose your favourite method for making onion rings, pointed or angular chains, & joining 2 picots together. If required, adjust the stitch count so that the concentric rings & chains lay niched.

Abbreviation/Notation :
OR = onion ring ; -/p = picot ; + = join ; RW = reverse work ; Ch = chain ; -- = long picot ; 
SS = switch shuttle ; rs = reverse (unflipped) stitch - optional ; ^ = dot picot with Only 1 first half stitch (not 1ds) - optional ; 1SCMR = self closing mock ring made of 1 stitch.

Round 1 : ball and shuttle, continuous thread

OR1: 6 – 6.

OR2: 7 – 3 +, p 3 – 7. RW

Ch :  2 –– 8 – 8 –– 2. RW

This forms motif#1. Repeat 5 more times, joining each new OR2 to that of previous motif, and also the last to the first.

Note : None of the chain picots is joined. They all remain free.

Round 2 : 2 shuttles, continuous thread. Refer pictorial here .

Attach thread to BOTH picots on adjacent chains of previous round. I joined them simultaneously, but you can choose your own method, keeping it consistent throughout. See Eliz Davis’ study. 

 

Ch : 2 –– 6 lock join

OR1: 6 – 6.

OR2: 9 + p 9.

Ch : 12 + SS mock picot R: 3 – 3. mock picot SS, 12, lock join

Ch : 6 – 2, lock join through Both picots.

This forms motif #1. Repeat 5 more times.

Round 3 - TOWERS : 2 shuttles, continuous thread.

Attach thread to the outside of any onion ring formation, and continue around the triple onion ring.

The ‘towers’ are made of curved chains where I used reverse or unflipped stitches. To avoid this, you can RW, and switch shuttle.

You can choose your favourite method to make the points. There are numerous options, including a seed bead, which I have listed at the end of the post.

To create the point at the top, I made 1ds SCMR, and the points at the side are made with 1 first half stitch dot picot. 

  

Ch : 14, lock join, 5rs, SS, ^ , SS, 7, 1SCMR, 7, SS, ^ , RW 5, SS, lock join on other side of        OR ,

Ch : 8, lock join through Both picots,

Ring: 5.

Ch : 3rs, SS ^ , SS, 5, 1SCMR, 5, SS, ^ , RW 3, SS, lock join on other side ring, and again          through both picots.

Ch : 8, lock join

This forms motif #1. Repeat 5 more times.

Block into shape.

NOTE : I found that when I made the ^ on the right side and continued with unflipped stitches, there was a tendency for that point to get sucked in. You may notice it on some of the spears. My solution : Make the ^. Then reverse work. Leave a loop of core thread as if you were tatting a SCMR. Work the 3 or 5 stitches, and only snug the chain. This keeps the point intact.

I really should’ve used another method to change the curves of the chain, and I did try a couple, but somehow settled for this finally. Not happy with my work.

In Anchor Pearl cotton size 8, this measures 4”. Side of hexagon is 2”.

FUTURE IDEAS

-         switch colours in onion rings, alternating the colours, as in block tatting.

-         use Victorian set for alternate onion rings.

-         change the tower curve from ‘spear’ to ‘trident’ (as in above trial pic)

-         padded double stitch (balanced ds) for sturdier spear chains
-         concentric chains for the towers (as in trial pic)
-         beads-          
-         Lee Buchanan gave me another idea to explore at leisure, to grow the tips as in real snowflakes.   

          

POINTED  CHAINS

A few options to make pointed chains : Scroll through for tutorial links (many are listed under different headings/sub-headings)   

-         Shoelace trick (SLT), switch shuttle or reverse work

-         Frivole’s one-stitch SCMR  

-         Jon Yusoff’s pointed chain 

-    Martha Ess’ folded chain (2 half-stitches) 

-         Usha Shah’s dot picot (or a half stitch dot picot as in pattern, to reduce 'bulk')

-         Ninetta Caruso’s right angle

-         Daniela Mendola’s mimosa knot