locked in place

One can never have enough bookmarks ! And I have been itching to tat one for quite a while. Hence what started out as a practice braid out of curiousity, got extended into a bookmark for my latest book.

Rings and Curves Variation

Braid to Bookmark

Original braid : 'Rings and Curves' by Elaine P. Gan

Variation : Judith Connors, on Craftree

This variation of the braid pattern was shared by Judith on Craftree as part of her description of & practice for Elaine’s Reverse Join (“The handy reverse join”). I have used the RJ frequently since the Wiosna doily & prefer it to the SLT (shoelace trick/overhand knot).

So here is my practice piece of the braid which I later decided to extend to a full bookmark.

Having used leftover green thread, it soon ran out. So I used Ninetta’s ‘elementary’ technique to add the chain thread and it felt a bit like deja vu. Loved the ease with which the thread was added & no ends to sew!

It was interesting to do directional tatting (RODS) in this braid - the changes were made in blocks of elements, just as in the Spinning Wheel mat 

With the main body length completed, I had to think of a tail. A lock chain would be too narrow for this braid. The tail needed some width to be proportionate to the width of the main body. Picots on both sides !

UPDATE: Pictorial for the Picoted S-Chain -https://tipsaroundthehome.blogspot.com/2020/04/picoted-s-chain-cords.html  . S-chains are a variant of the zigzag chains.

For the few who actually read through my posts, do you recognize this? I tried it with metal here.

Yes, it is not a pearl tatted braid, but a S-Chain with picots. And the S-chain is a simple extension of a lock chain with complete stitches. Refer samplers # 10-12 here for comparison. I love how the stitches are diagonal to each other !

The tail still felt too narrow; so I decided to go for 2 tails & snipped off after desired length. And as always, the NanoMoment you snip, there comes this Big brainwave sweeping in all kinds of regrets !  Why have 2 separate tails ? Why not have them interlaced ?! I could’ve simply turned back ….

Oh well, damage was done. Reconnected threads to base & started 2^nd tail, intertwining it with the first. Here, I used Martha’s ball thread join (explained in her Butterick Butterfly Bookmark pattern) to mask the links & keep the picots seemingly intact.

Look carefully & you will notice a green join on the lower left overlap & a pick one in the upper overlap.

Threads used : Anchor Mercer size 20 Art 4054. (pink – 052; green – 0241)

Measurements : Main body – 5½” x 1¼”  ; Tail – 4 “ x ½”

Techniques I used : 2 shuttles, RODS/directional tatting, reverse join, S-chain, ball & thread join, adding new ball thread in a chain

Without planning it, this bookmark has 2 adaptations/variations of the lock join – the reverse join & the ball thread join. The latter is already covered in Part II of the Joins series, & the former will come later.

My Observations/thoughts on Reverse Join :

• RJ eliminates the visual dip caused by a lock join, and another dip when using SLT (I am not a fan of SLTs). Due to the encapsulated thread, no dip is produced.                     
• There will remain a colour blip which can be incorporated as a design element.
• RJ is much easier to undo than a traditional LJ, because of the encapsulated thread.
• In the bookmark, I deliberately used a down loop throughout to make the RJ. And since I was tatting fs/bs, some of these turned up as up loops. It doesn't change the spot of colour, but it Does change how the colour bar appears ! 

I enjoyed tatting this braid to bookmark - although only rings & chains, it needed one's attention. Another page in my learning turned :-)

Many thanks to all the wonderful tatters named in this post - 

you enhance my learning at every step !

Related Posts : Shuttle 2 to the rescue

Chains in shuttle tatting